surface gluing中文是什么意思

发音:

中文翻译
造句

板面上胶
企口锁

surface n. 1.表面；地面；水面；广场，空地。 2.外观，外表 ...
glue n. 1.胶，胶水。 2.各种胶粘物。 st ...
gluing 胶合，黏合; 胶结; 涂胶; 黏接
cold gluing 冷胶合; 冷室温胶合
continuous gluing 连续胶合法
dry gluing 干式胶合
edge gluing 侧面胶结; 棱边胶合
end-gluing 端面胶合
foam gluing 发泡粘合; 泡沫胶合
gluing machine 上胶机，涂胶机
gluing rock 铁胶粘土; 黏合土
gluing theorem 胶合定理
hot gluing 热胶合; 热压粘结
primary gluing 一次胶合; 预胶合
pvac-gluing 热冷熔胶
secondary gluing 二次胶合
spot gluing 点滴胶合法; 点胶合; 点粘结; 点状胶合; 局部胶合
thread gluing 粘扣
wet gluing 湿性胶合法
wet-gluing 湿胶合
application of gluing paper on the edges 胶膜纸封边
book back gluing machine 书脊上胶机
book gluing machine 书籍上胶机
carton gluing machine 纸箱上胶机
case gluing machine 纸箱上胶机

"查查词典"手机版

千万人都在用的超大词汇词典翻译APP

例句与用法

The early studies are mostly focused on the method of gluing piezoceramics on structural surfaces , which has some disadvantages such as difficulties to protect the ceramics and the connection wires , bad coupling with only one surface glued on the base materials , low signal - to - noise ratio etc . these problems can be solved using the embedded piezoceramics , and furthermore , the piezoceramics can be placed in the optimal positions , especially in the optimal deepness for the piezo - actuators , according to an optimization algorithm befor e they are embedded , so the actuator effects and sensor signals are thereby enhanced
早期的研究主要集中在表面粘贴压电片的结构，表面粘贴压电片具有一些无法克服的缺点。本文着重进行利用埋入复合材料结构的压电传感器和压电驱动器对其振动进行主动控制的相关理论和实验研究，并介绍其相应结果。埋入型压电材料的优点主要是能保护压电传感器和作动器及其连线、增强压电材料和基体材料的耦合、优化埋入压电陶瓷的深度和厚度可增强压电传感器的测量信号并提高信噪比等。
The carbon fibers with low strength are broken easily according to thermal tension and bend stress damage models , and the carbon fibers with high modulus are broken easily according to thermal shear stress damage model in spite of less damage caused by heat . the carbon fibers with surface glue of epoxy resin are damaged easily in physical and chemical ways because of high oxygen extent and rigidity of epoxy resin
低强度碳纤维容易在热应力拉伸或弯折破坏模式下损伤；高模量碳纤维高温损伤小，但国防科学技术大学研究生院学位论文容易以热应力剪切破坏模式下断裂;环氧树脂表面胶刚性较大，氧含量较高，使碳纤维容易受到化学损伤和热应力弯折损伤，均不宜用来制备c灯sic复合材料。